Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi.
I am using the nRF52810 for Bluetooth SIG certification.
S112 6.0.0
SDK 15.0.0
I am testing using ICS of QDID 102861 and 49943, but a failure occurred in the GLS...
We are upgrading our product from SDK15 to SDK16 using DFU over USB. When we perform a DFU update (BL, SD, and App) form SDK15 to SDK16, it works fine. Then if we perform...
Hi! I'm studying the basic codes of the BLE Blinky Application for peripheral! ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_blinky...
Hi,
I'm making a custom board with NRF52840 and would like to confirm some schematic/layout considerations for things I couldn't quite find in other posts. I apologize if...
Hi Nordic Team,
I am using SDK 16.0.0 with Softdevice S132 version 7.0.1 on the NRF52832 and using SES v4.52c on Linux. I have managed to run and sucessfully execute the...
I use the following code to enable a timer that clears itself to loop continuously via the compare0-clear shortcut. (I then use other compares, PPI, and GPIOTE to output pulses...
Hi Nordic guys,
We just integrated the AGPS function using SUPL library with the GPS driver to accelerate the GPS fix time.
We tested our code with near windows environment...
Hi,
I managed to download the latest firmware on my thingy91 and it looks working properly on the LinkMonitor. Anyway, it stays always in searching LTE and never goes to...
hello everyone. We found a problem. when nrf52832 is working, after the core power supply is sudden short and release, the power supply mode is LDO and the current is about...
I have a device that has multiple NRF52832 modules
Is there any issues with setting the mac address of each of the modules to the same thing...
e.g. would there be any...
Working with SDK v16 (S140 v7.0.1) I get error code 0x10 (NRF_ERROR_INVALID_ADDR) when calling nrf_sdh_enable_request(). Setting into that function I see that the error code...
My application uses the nrf9160 in eDRX mode. I regularly have the problem, that when switching the modem to OFFLINE mode (same for POWER-OFF mode), the modem is not responding...
Dear all, I have a plan to use NUS service alongside with proxy Mesh. I tried to find documents about mesh performance with Nus service? Could you please give me more information...
I wrote two applications, and both will never know what application starts first. So I design a handshake that works something like this.
receiver
Set to receiver, look...
