Note: I am aware that NCS v3.4.0 recommends DTS-based partitioning over Partition Manager. However, I was unable to get the DTS-based approach working for my specific configuration...
Due to the great advice & guidance from Nordic 3 years ago (Andreas Haugland & Vidar Berg), see:
and https://devzone.nordicsemi.com/support/311747 we have been happily using...
Problem Description
The custom hardware board cannot boot normally after flashing the firmware. However, the exact same firmware image works perfectly on the official nRF54L15...
For my project I want MCUboot with the upgrade image placed in the external flash, and TF-M. I am not able to get this combo to boot however, and I suspect the reason is that...
Hi!
I am trying to do a DFU with external flash, using a nRF54L15-DK development kit.
To evaluate this feature, I use the l9_e3_sol example available on GitHub (I use...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Dear Sir,
Using SDK 16.0 for NRF52833. My application uses NRF FDS lib (flash data storage)
Immediate fds read after fds write gives 0. But after a board reset I get...
Hi,
I am using nRF52840 S140 with ble_app_blinky application. I have a basic query of GPIO configuration when moving from Bootloader to Application.
We are using Secure...
I'm using ble_uart_app and wanna Low Power Current Consumption but its consuming 330uA. disabled the nrf_log form sdkconfig file. main code is below. Please let me know what...
Hi,
When nRF9160 is used as a co-processor and an external host MCU is used to interface with nRF9160, what are the serial interfaces that are allowed? The at_client example...
Is it a better choice to use the NCS for nRF52840 development, given that it is the new platform going forward? Am I painting myself into a corner developing with nRF5 SDK...
Hi,
I'm trying to develop buttonless DFU and followed below guidelines and got to work all the way to step6. Thank you.
https://github.com/gamnes/nRF52832-buttonless...
I want to build my own board configuration:
The default configuration of the board is as follows: ncs?v1.2.0,zephyr?boards?arm?nrf9160_pca10090
How do I generate my own...
Hello
I'm using NRF connect the app to perform read and write on nrf52840 board SDK ver of 15.0.0.
I can perform the write and read operations using nrf connect app, and...
Hi
I'm working on a custom PCB based on nRF52840 soc and SDK version 16.0
currently I'm trying to interface my MCU with an external flash of model MT25QL01GBBB
my...
Hi,
I would like to interface ICM20948 with nrf52832 and communicate over TWI or SPI. That thing I don't understand is the logic voltage of the bus. In nrf52 specifications...
Hello,
I went through the instructions in the Getting Started Assistant to setup nRF Connect SDK for Linux but I am getting the following error when trying to build a project...
Hi,
I am programming nRF52840 dev kit (SDK16) as a peripheral with S140. Smartphone is central.
data needs to be transferred between both.
I need the dev kit to consume...
Hello, I’m using nRF52840 with SDK 16 and SD 7. My purpose is to save as much power is possible using high-frequency clock (32MHz) only during periodic duties and BLE activity...
What are best practices for updating an nRF52832 via UART from an nRF52840? There seem to be at least two problems to solve:
Transmitting the 832 image via BLE to the...
Hello,
I'm measuring the idle current using a PCA10040 DK, SDK v16.
Finding that the idle current is about 3uA (which I think is correct) after any debug operation like...
