Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi Guys,
I have managed to get the BLE DFU demo service working fine (dual bank) on nRF51822 EK. I use a Linux Python program ( bitbucket.org/.../nrf51_dfu_linux) (with...
what is the detection speed, when the beacon
enters into a wall unit area? With their 868 beacon they can
detect in 0,2 seconds. Is the nRF51x22 in sleep mode and does it...
For our application, As I used 24LU1(host) with 51822(device) be the platform.
I hope to transmit Audio data with 8 kHz, 10 bits data format. To commit the requirements ...
Hi,
I have installed "mastercontrolpanel.3.4.0.8098.x86.msi" on my PC, I could not find my master dongle after runing it with my dongle be inserted in USB slot. The screen...
Hello all,
I am getting an error when my device disconnects from the client. The error occurs while bond storage due to data limit exceeds.
err_code = ble_bondmngr_bonded_centrals_store...
Hi all,
I have made some modifications to the bootloader example project (dfu_dual_bank_ble, s110) to get a bootloader that meets my requirements. It is working ok, I can...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
