Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I am a newbie and just started working on the nrf52840 board. I started by using the example "ble_app_uart" and implemented the I2C module to read IMU sensor data and...
Dear all,
I am interested in a BT mesh modules that support precise time synchronization between the modules (microseconds). This is required for sensors application that...
Hi,
I installed nrf Connect SDK 1.2.0 using the nRF Connect 3.3.2 App - Toolchain Manager. (Windows 10)
Using SES for Nordic v4.52, I opened the asset tracker project...
Is there any way I can scan for a short period of time with a duplicate filter on so that I only get 1 packet form the advertising device in one scan window.
For example...
I recently purchased and downloaded the nRF9160DK. The DK User Guide v0.7 does not match the Altium design files schematics and neither match the application schematic in...
I have project with nrf52832.
every second, i want send 11k byte data from nrf52832 to android app, but it is loss data. (i used phone ble 4.2 loss about 1-2% packet)
...
Hi,
Been starting to program the thingy91 and faced some issues. This is the second attempt after failing on the PC and now using the MAC.
Managed to follow the steps...
Hi Sir,
I use the example ble_app_uart_c, the program runs to APP_UART_FIFO_INIT() in uart_init(), an error will occur, and the program jumps to NRF_BREAKPOINT_COND -->...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
Hi, Im new here and microcontroller programming... I curently waiting nrf52840 PDK so Im only quick read SDK and documentation... Before Im program only devices with .NET...
Hi, I cannot open my project using SDK v1.3.0 (nrf9160dk_nrf9160ns selected board) I installed the v1.3.0 using nRF Connect v3.4.1 - Toolchain Manager I already downloaded...
Dear Nordic: I have issue about connect handle. My product supports 1 peripheral and 3 central roles. 1. For this configration, i am not sure handle 0 is resverd for peripheral...
Dear all, I have a question about IV index and sequence number in mesh network. If i have 3 nodes success provisioned. I will only power on 2 active node ( node 1 and node...
Can't see why this is occurring. I've checked my custom board and the reflow of the chip under microscope. The doc indicates this pin isn't linked to a peripheral. Despite...
