Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
Hi,
I'm developing a BLE mesh project using Mesh SDK v4.2.0. I want to change the Tx power of the product in real-time, e.g. from 0dBm to 4dBm, 4dBm to 8dBm.
I've read...
I have an application that is running for a while and then it crashes.
Execution goes to softdevice_fault_handler(), calling it with parameters: id=1; pc=0xf764; info=NULL...
hi all
A silly question here , I am prepare to meet some security compliance , one of them is about delete files permanently.
I wonder how to get this done on nRF51822...
Hi,
I would like to wake the nRF52840 SoC from sleep via a GPIO High Pulse input.
What is the minimum allowable pulse period do I need for it to successfully wake up...
Hello,
I have the following application code (based on the template project from the SDK):
The receive callback is working and I get all the characters from my terminal...
From the datasheet I understand that any pins in port0 can be used as SPI. But I tried using the pins defined in nrf-sdk here and but there is no response. After searching...
Hi!
I am kind of DIY person and have a lots of time in COVID, I am a beginner to Nordic family, few months ago I implemented MPU9250 with NRF52832, I was able achieve...
Hi !
I am working with nRF52 DK to drive the nRF52832 and a sensor of Maxim Integrated.
I am using an older version of the SDK (14.2.0) because i need to modify an old...
Hello,
I was looking at power profiler (just playing with it) and I run it without proper setup on nrf52840DK, after that It seems that dk does not execute any application...
My application is again having troubles with opening an AF_LTE socket. It hangs indefinitely on the call to socket(AF_LTE,...). This code has been running successfully at...
i use nrf51822 and uart project
i need disable only RX when tranmitsion and reuseable when tranmistion complete. i tried
//NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled...
Hi
Do any of the Soft Device versions support the periodic advertising feature which is part of extended advertising and involves AUX_SYNC_IND PDUs? I looked at the API...
