Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...
Hello,
I am using nRF52840-pdk with Keil5 and nRF-go studio for development purpose.
I am facing an issue that after new firmware version upload from nRF-go studio to...
Hi everyone,
Currently, I was developing an application on top of Zephyr. I notice that NRF52 SDK provides library for MQTT-SN protocol. However, my application needs to...
Can the TCLK timeout be changed? I have a ZigBee device that joins and performs a key exchange but then is forced to leave the network 12 seconds later due to a TCLK timeout...
I am working on a project that I need to scan bluetooth devices. I am using nrf52832 as a central, sdk 15.2 and s132 v6.1.1. when I activate the advertiser tab on nrf connect...
Hi,
I haven't ran the FOTA download library in a while and I was just testing it. I don't seem to be getting any of the FOTA_DOWNLOAD_EVT events. I am running nRF SDK v1...
I am using nrf52832 as my cnetral and also nrf52832 as my peripheral . i am connected central with peeripheral using ble multilink example code. but it shows only 16bit uuid...
I am using nRF 9160 mqtt_simple example to connect to a custom mqtt broker address as shown below
The following is the mqtt.fx application
I changed all the necessary...
Radio callback not occure after advertising stops.
I changed ble_app_beacon example to support timeslot as follows.
I put "NRF_LOG_INFO("radio_callback:%d", signal_type...
Hi, We are using nrf51822 in our device and Device firmware update is implemented in it and we are being able to do the device firmware upgrade by using nrfConnect app. Now...
1. Some Bluetooth originals will provide software and hardware tools for Bluetooth keyboard production testing. 2. Does Nordic provide production tools for similar use? 3...
What is the best way to send about 1600 bytes of sensor data using ble5.0? I would like to receive about 5 times per second. Also, is it possible to configure 1:n like this...
Hi I'm a bit new to programing with nordic.
I'm trying to use the nrf_gfx_background_set function to display an image on an epaper panel. I've already written code that...
