Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
hello Nordic
i am working with the nrf52840 , sdk 16.0, s140
i am using the peripheral ble_app_blinky example as a base
i added saadc and twi, (spi and uart will...
Dear supporters,
I am designing an antenna for the chipset NRF52832. After several experiments indoor and outdoor environment, we got some issues. Besides, We got the same...
When I call sd_ble_gatts_hvx() it returns 0x3400 and I'm not sure why. The error indicates the sum of these three errors:
NRF_ERROR_STK_BASE_NUM (0x3000) NRF_GATTS_ERR_BASE...
Dear Members,
I tried to include temperature into my ANT HRM receiver code,
but when I add components\drivers_nrf\nrf_soc_nosd
I got plenty of errors, what do I...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
I am working on a project based on the ble_app_hrs_rscs_relay example project which I have largely extended with many additional services.
For example I am offering an additional...
Hi
I am working on nRF52832 , I want to store the data in NVMC . so I am trying to write the data blockwise , I saw the layout each page consists of Block 0-7 .To each block...
Hi everyone,
Is it possible to implement a USB device belonging to the Personal Healthcare class with the nordic nrf52840 DK?
NRF supports Personal Healthcare USB class...
Hi, I have written these 3 functions to erase/read and write. When I write any value from address 1 it gives following wrong output(0 1 2 3). But When I start address from...
Hi nordic team，
I use the nrf52832 EVK ,I want to connect MIC and speaker to the EVK.
I read the nRF52832_PS_v1.4.pdf, and i guess following interfaces can be used.I don...
Hello
I am using Linux PC
nrf52832
chmod 777 to the nordic serial port
using the bt_nus_shell script :
sudo python bt_nus_shell.py --name BT_NUS_shell --com...
I want to use nrf5340 on DTM mode (installed through nrf connect) to test Carrier frequency offset for CTE packets using CMW500. However, CMW uses power trigger to find the...
I have developed a custom PCB based on nRF 9160. I have followed the connections as per the attached image
Can I use Segger Embeded Studio to program the custom PCBs. If...
Hi there!
How i can put nrf52840 NCP module into low power mode or turn it off? By SPINEL_PROP_MCU_POWER_STATE property of Spinel protocol getting error - "Prop_not_found...
