Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Because the nRF52840 consumes an additional 1mA when QSPI is activated, Nordic has previously recommended deactivating QSPI when not in use, which in practice means deactivating...
Hello DevZone,
Perhip: PCA10040 SDK 15.0.0, SD 6.0.0
Central: PCA10056 SDK 15.0.0, SD 6.0.0
I am working on a BLE project and we need to make sure our link is secured...
Hi,
I am building an application for Thingy:91, currently using SDK 1.3.0. The application is supposed to collect data using BLE and forward it with LTE to the MQTT broker...
Hi,
I wanted to read all the android notification using an embedded BLE device..
I have gone through BLE_ANS example which is in nRF51 SDK, All i want is to implement...
Hi, I'm working with nRF52840DK. I need to run in Direct Test Mode, and to see RSSI & PER. I tried nRF Connect - Direct Test Mode, but it shows only the number of received...
Hi engineers,
I want to transplant demo "usbd_audio" from pca10056 to pca10100, what should I do?
I found a relevant ticket said that
Change board config.
Change...
Hello DevZone,
For a project I'm using the TAG-4 NFC writeable NDEF message example in my SDK and I had a question if this message is always stored in flash or if it is...
I have two nRF5340PDK, both of which would have worked normally. Then I accidentally download the firmware of 52840 version into nRF5340PDK by GProgrammer, which made them...
Hi,
How can I know whether the BLE link between my nrf52840 device and the pc (while connecting via NFC) or the mobile, is configured as a half duplex or a full duplex...
Dear,
I am trying to get secure serial DFU working on our custom board, which is connected to another controller through 2x UART(P0.02, P0.03, P0.30, P0.31) without HWFC...
Hi, I am developing a central application that should get data from a single or even multiple primary services with multiple characteristics in Zephyr. I am using the central_ht...
I'm trying to build the light switch example. I have downloaded the nRF5 SDK for Mesh v4.0.0 and the nRF5 SDK v16.0.0, and place those 2 extracted folders in the same folder...
It works when I use I2C_2 to communicateon nrf9160. The register value is successfully accessed when i2C_reg_write_byte() is called.
9160dk_9160ns.overlay:
I want...
I am trying to use peripheral/spis as a reference for configuring my nRF52840 DK as a slave. The SPI clock frequency is 1 MHz. The SPI master is another micro-controller....
Hi,
I am using nrf52832 development board with sdk 17.0.2 and S132 softdevice. My requirement is to scan and advertise at the same time. I am using the ble_app_template...
