Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I have an application that will have up to 20 devices communicating with a gateway. Each device will need to send around 2MB of data every 5 minutes. We would like to use...
Hello.
I try to BLE and GPIOTE.
The reason for using GPIOTE is to read data from the temperature sensor.
And I want to sending data of temperature sensor by BLE...
Which type of PCB antenna should i use for BLE beacons based on nRF52832, nRF52840 and nRF52805 for longer range applications.?
Can i use the same antenna used in nRF52DK...
Hi All,
There are few chips that Nordic supports Direction Finding.
nRF5340,
nRF52833
nRF52820
nRF52811
Is it possible to know the recommended chip I should...
hi all,
NRF_ERROR_INVALID_STATE is coming when i initialise Ble_stak_init form nrf_sdh_enable_request() function.
I initalised ble once and disabled using sd_softdevice_disable...
Hello,
I am developing on the Garmin LIDAR-Lite v4 , which uses an nRF52840 internally with the programming pins exposed. I am able to run my OpenThread application on this...
Hi
while developing I've discovered that the current tickless implementation using RTC causes the idle task to loop for one tick before waking the next task up.
I've instrumented...
Platform: nRF52840 { development kit } SDK: nRF5_SDK_16.0.0 Can sdk_config be used to remap any pins for used a SCK and MOSI and MISO? Specifically, can the following mapping...
Hi all,
I'm running into this error when trying to compile anything for the SPI library in Cmake
CMake Error at ../../../cmake/extensions.cmake:372 (add_library):...
SDK v16.0 NRF52832
Hi
We have been using the the NRF Bootloader for sometime, but we have encountered an issue where if the DFU (Serial) is interrupted (ie, USB cable...
Hi,
I've been using the Thingy:91 to communicate with some sensors. One of this sensors is causing us some trouble: sometimes the I2C communication with him seems to fail...
Hello
I would like to commission my Thread network but my Thread network is isolated (I have no wifi) but I have bluetooth which works in parallel to the Thread network...
I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them, I don't want to use PPI mechanism I just want to run my ISR in time...
Hi All,
I have developed my application for the nRF52832 (SKD15.2) on top of the TWI sensor example. I moved from the legacy TWI driver to nrfx due to the data length limit...
