Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
There is an option to 'Clone device's services':
A message pops up briefly to say that it's done it:
But it doesn't say where it's put it, and I can't see any...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
Using NCS 1.3.1.
Why is nrfx_spim_xfer() asserting when using NRFX_SPIM_FLAG_HOLD_XFER flag and a ss_pin ?
When not using a ss_pin in the spi config but configuring with...
HI,
I was trying to update firmware on thingy 91 using MCU bootloader. Now when I trying to upload again it is keep showing one error.
Error while probing devices: Error...
Hello,
I'm using nRF52832 and SKY66112-11 PA/LNA connected to increase the range. I'm using nRF5 SDK 17.0.2 and nRF5 SDK for mesh 4.2.0
I followed this guide to use PA...
Hello everyone,
I'm programming for nRF52833, using SDK17. When I program for scanning filter (SCAN_NAME_FILTER and SCAN_UUID_FILTER) and debug, I got these errors. I don...
