I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I have recently started understanding nRF52840 using SDK v17 and soft device S140 v6.0. I'm using Keil as my dev environment.
Opening any of the SDK example in Keil, when...
Hi,
I am trying to integrate ble based bootloader into my existing system running on nrf52840. I am using SDK 16 v7.0.1 with sd140. To test the process, I have added the...
Hi, I am working on the ble_app_template project. 1-How can I enable simple pairing without NFC? 2-Also how can I set pairing code? 3-Is the write way to secure characteristics...
Hi, I am developing the project where to read the sensor data and send the values to the mobile application as User Interface. I have built the Board with nRF52832 and using...
The size of the FIFO is sufficient. The value is extracted from the FIFO after being received by the UART. Repeat UART reception.
APP_UART_FIFO_ERROR occurs in the above...
Hi everyone,
I'm using SDK 15.0.0 S132v6.0 and looking for a way to get an event when the advertising times out. I discovered the softdevice_ble_evt_handler_set() in this...
Hi,
I am developing a device based on the PCA10059 board, SDK v15.3.0, and softdevice v6.1.1, and I want to imply that I am using the FDS module with 20 pages in my firmware...
Even after I get a license for the Nordic stuff, SES won't show an installed activation:
The license "installs" fine though:
And I do have the "Nordic" version...
Hello,
When I try and use nRF connect Programmer to update the modem firmware via USB it fails each time in the second step (Modem Firmware Update) with the error message...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project, which acts as a central, and an IOS phone as a peripheral. I have a read/write...
I have an nrf52833 wired up to 25 switches and detect changes via the pin SENSE configuration triggering the GPIOTE PORT interrupt. My interrupt handler: 1. reads the pin...
Due to whitelist limitation of 8 peers, I am doing manual filtering of bonded devices. I am trying to use pm_address_resolve function to figure out whether I have previously...
I am using nrf52840 DK and communicate with Raspberry Pi 3 through UART port. The Raspberry Pi is used as a gateway. The baud rate is set at 115200 default on both nrf52840...
Hi, I am trying to integrate ADC in my project( ble_app_template ) but getting garbage data. I have nothing connected with pin P0.4(NRF_SAADC_INPUT_AIN1) . (Means not applied...
I am budding Embedded Engineer, currently, I would like to learn how to program nrf52dk. While I am exploring info center, Peripheral examples I have noticed that most of...
