Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear Nordic Team,
I use a custom dev board with the nRF52832 SoC and the nRF5 SDK v16.0.0.
I need CoAP functionality for my project. I managed to get the CoAP Examples...
Hi guys, I am developing an mqtt-based app using board nrf9160. I tested the mqtt_simple example but it does not work. Here is my setup.
+ Broker server: test.mosquitto...
Hi, I'd like to set the alarm state of a minimal power configuration cluster that only has the attributes "remaining battery percentage" and "battery alarm id". However the...
Hi,
Is it possible to write to the UICR (with SES) without erasing it first?
Normally the boot loader sets the correct values in UICR, but for development I want to have...
Hello,
lately i've not been able to connect to NB-IoT network as i did before.
Long story short:
I'm working with nrf9160 since 3 months and i have been able to connect...
When the macro NRF_SDH_BLE_GATT_MAX_MTU_SIZE is changed in the sdk_config.h file of any example from the ble_peripheral folder, the slave sends the message Exchange MTU Request...
Hi,
I am using nrf mesh sdk 3.1.0. with nrf52832.
For iv update one condition is iv_timeout_limit_passed(m_net_state.iv_update.timeout_counter). The timeout_counter value...
Hi,
I am evaluating ble peripheral with nRF52840 SDK 16 and SoftDevice s140 on windows 10.
The SDK is copied at location: C:\Nordic_Semi\nRF5SDK160098a08e2\
The SoftDEvice...
Hello,
I am not able to connect the dots. After setting up the beacons, ( adopted ble_beacon_app from Sdk 16 ) how can I perform localization algorithm ( trilateration)...
Hello. I try to configure radio at NRF52811 to prepare antenna switching and get correct I/Q samples from different antennas. I have 2 antennas that are 6 cm apart from one...
hello, I try to make an application with 6 different services. I used the ble_custom_service tutorial to create my different services.
I manage to work without problems...
Hi,
I am working with the bsp.c functions. One of the actions is BSP_BUTTON_ACTION_PUSH, which the value is 1. I would like to know at which electrical signal it is related...
Hello All, I am having a trouble with the nReset Pin during Deep Sleep. The issue is that the board is waking up from Deep Sleep due to floating nReset Pin. I am using a nrf52480...
Hi,
I am currently working on a product based on an nRF52832 (SDK 15.3, S112 6.1).
The firmware uses the Nordic UART Service to receive and send data from and to a smartphone...
