Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
Hello,
I have nrf52DK and I want to deploy templates from S130 protocol to NRF51822XXAC. Any tutorial or guidance would be greatly appreciated.
Thanks in advance.
Hi to everyone!
I am working on the SDK 17.0.2 and my project contains nrfx_twim.h functions.
I have a problem to understand the changes that i have to make in the sdk_config...
hi..
I am using nrf52832 and 15.2 version sdk . my laptop 64 bit wndows , there is no software for 64 bit windows , so i installed the 32 bit software
i am getting the...
Hi, I'm just wondering if there could be any chance that the GPIO can be used as ADC? I had my gas sensor output wired to GPIO (P0.03) instead of ADC (AIN0-AIN7) pins. TIA...
Hi,
I tested UART app(nRF Toolbox) by iPhone for scenario: erased bonding info of peripheral but iPhone, then establish connection between iPhone and peripheral.
Here...
I am trying to integrate code on hts221 with an nrf52832. I am using sdk15a for referring the .h and .c of hts221.
NRF_TWI_MNGR_DEF(m_nrf_twi_mngr, MAX_PENDING_TRANSACTIONS...
