after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I have got three nRF52840 Dongles to test Bluetooth mesh. I have been going through the devzone queries and found that many people have previously asked about SDK...
Hello,
I am using the nRF52832 with the s132 SoftDevice. I've been trying to interface the VL53L0X sensor to get ToF readings. I'm using the code of this driver . When calling...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
Hi,
I'm developing a program using SPIM instance 1 on nRF5340 PDK, with nRF Connect SDK 1.4.0.
The problem I met is exactly the same as this post . If I want to use a...
NRF52832, nRF52840 is under consideration for development. Because of the implementation of Secure Boot and Secure Key Storage capabilities, we want to choose the nRF52840...
Hi,
I was able to upload a binary file before, but not able to upload a binary file to nRF connect app in order to FOTA.
Could you please help me to upload a binary file...
I am trying to compile and run the ble_app_hrs example for an nRF52810 dev board, using Segger Embedded Studio v5.34. I am using nRF5_SDK_17.0.2_d674dde, with s132. This is...
Hi,
I am looking for a working example for upgrading the MCUBoot itself when we have the configuration B0+MCUBoot+APP, especially wrt to SLM application.
I have gone through...
Hi, I am developing using Segger Embedded Studio.
I downloaded the module and checked that output/debug/Exe has a .hex file.
Then can I download this output file back...
Hello,
We are testing Angle of Arrival feature which was released in Bluetooth v5.1 We are currently using Texas Instrument CC2640R2F and TI angle of arrival board to...
Hi,
I'm using nrf52840 with BLE functionality.
I don't use sd_ble_gap_tx_power_set in my application.
Does it mean that I'm using default power (dbm)?
What is the...
Hi,
i am trying to interface an external spi flash memory with nrf52832 to store temp. data.
i tried to read the manufacture/device id but i am getting wrong data.
my...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
