Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
When working with AT#XHTTPCREQ we have encountered the following provlems:
1. Sending AT Command `AT#XHTTPCREQ="POST","/upload","Content-Length:3357",3357` with the payload...
HI!
I'm currently working on a project where I'd like to send and receive BLE messages using my own channel hopping mechanism.
I've read into the 17.0.2 Examples ...
I am having trouble connecting to an nRF52810 in a uBlox BMD-330 Eval Kit.
It has previously been successfully flashed with custom firmware but, now, when I try to connect...
The specifications for Flash programming in section 4.3.7.1 page 21 is blank in the nRF52810 Product specification 1.0. Can you please provide the values for this table?
Hi all,
I am not able to update the modem firmware over usb/mcboot with the programmer on my Thingy91. I have tried both on linux and win 10, the problem is the same. The...
Hi,
I have been using the NUS on nRF52832 DVK with no issues, however, when I migrated to the nRF52840 DVK and a custom board based on the 52840, the NUS characteristics...
Hello Nordic Community,
I am currently following the SMP guide provided here: https://docs.zephyrproject.org/latest/samples/subsys/mgmt/mcumgr/smp_svr/README.html
The...
Hey,
I am wondering if it is possible to run MTD and SED on the CoAP server on nRF Connect SDK v1.4.0.
I have looked at the question " How do I set up CoAP Server whit...
Hello,
We are going to design our new product using NRF52832. Please suggest if there is any other better IC which has higher transmission range, higher RAM and with less...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
