Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello
I'm working on sdk v17. I want the LED to be printed out like a wave when I receive certain data from the app. (5 Times)
It is simple to use 'delay' and 'for' as...
I had my first encounter with Nordic chips a couple of years ago. To evaluate the devices, I used an nRF52832 to implement a small helper project. I was very impressed: it...
Hi Team, Is it possible to use the BLE NRF52832 module for audio applications like attending phone calls, listening music etc. If it is not possible with this module could...
I wrote this code to make a 1MHz signal clock with timer and GPIOTE.
It works fine without softdevice, but when I modify my app to use BLE, gpiote doesn't work (I...
Hai ,
I am using nrf52840 and 15.2 SDK for ota over BLE. I have made bootloader for OTA over BLE and tested same with nrf connect application using dfu package zip file...
I tried to make a copy of the Asset Tracker example application to start my own project. However I cannot get it to load in SES. I'm currently on the Master branch of nRF...
Hello,
Based on the DFU documentation, you should be able to download an updated soft device as long as the "major" number of the soft device does not change. This was true...
I recently designed a PCB and have been testing it.The PCB mainly consists of the Bluetooth Module BMD-350 ( based on NRF52832 SOC ) and HX711.( There is an accelerometer...
Hi. I have a question regaring the nRF52833. I want to program the MCU using ArduinoIDE and I'm not sure if I have to use a programmer to program the nRF52833 and if so do...
SDK 15.3
SD S340
Bootloader implemented to update over GSM and BLE. BLE update code is taken from example secure_bootloader_dfu*. GSM update code is custom made. SDK is...
I set up nrf52832 that it is called proxy device, i create a loop that proxy device will sent 20 message to app phone (Android) within 100ms. But my app (Android) receive...
So I'm not sure that this is an error, but it is a little annoying. I have an application that sends sensor data using ble_nus. Works great, except that mixed in with my data...
To the kind attention of Nordic support team,
In case of a device and host ble bonded, I'm giving a look at disconnection reasons codes due to (1) host entering sleeping...
I have build a project, and it has been running normally. Now, I want to test a font data, so I created a function. But strangely, although the compilation has been successful...
We are developing iPhone application that configures mesh boards. If we try to send several messages in a row (specific case: trying to distribute application key and then...
