Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello DevZone,
I am developing a system that has a SoftDevice, UART bootloader, and application. The SoftDevice is S132 SoftDevice v6.1.1. The UART bootloader and application...
RTT seems to be mostly working using the viewer with the command:
JLinkRTTViewer -device nRF52840_xxAA
It seems I need to re-connect each time I start a debug from SES...
Hello Nordic
We are in the process of product development and at the moment we need a chip that transmits stereo audio to any BT headset. That it is possible to control...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
Hi,
I know it's a very common question, but I still haven't fully understood. There is nrf52832 on the peripheral side, there is ble dongle on the central side.
How does...
Hi,
I am trying to get a project to compile using the the segger studio. I have copied one of the example applications and converted it according to your instruction here...
Hello,
I want to add a new driver directly in my project (out of tree), so I've add the differents files, as in the picture below.
When I compile, I get each time...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
Hi Nordic Team,
Some time facing Connection issue in Mobile app and some time device advertisement is not getting in app.
I am using below chipset and configuration. ...
Dear all, I try to self provision device by it self following steps below: Step 1 : Bind key Step 2 : Subscribe to topic
Step3 : Set publication topic
Step 4 The main...
