Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
My setup: custom board using nRF52840, Segger Embedded Studio 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4
I used a couple of your projects as a starting point for my code. Specifically...
Hi,
In my proejct, I am using WFE(); in some while loops because of core low power mode.
For example, waiting for time_out flags like codes below.
I am wondering if...
Hi All,
I'm new to the nordic product. We previous using TIcc2642 as development board. And we would like to test our application over different hardware. Is there any...
Im using CUstom BLE tutorial example and it works fine. But i just wanted to know, in which section is the text data for logging occuring. Ex: "notfication received from ...
Hi community !
I want to know if a code works on nRF52840 DK PCA10056 will work on nRF52840 PCA10059 ? On both, i will never use physical input (button led or gpio) i'm...
Hello expert,
I just jump from TI. Could anyone tell me if nordic has any chipset like TI CC1310 which supports direct access to the receiver I/Q quadrature samples?
...
The Thingy91 GPS system sensitivity is terrible. Getting the GPS to lock on takes forever, and many times doesn't lock on at all, and if it does lock loses the connection...
Hi community ! Here : https://devzone.nordicsemi.com/f/nordic-q-a/62414/different-behaviour-with-same-program-and-boards i get some problem with different behaviour when programming...
I'm using the Laird Connectivity BL654-DVK board as a basis for evaluating the nRF52840 for our application.
I started by using the .../examples/ble_peripheral/ble_app_hrs_freertos...
Hi,
When we do the UART stress testing with serial_lte_modem sample, the slm will crash by sending AT commands with interval 100ms.
the debug log will show "<wrn> at_host...
Hi ,
I have question about the specification of CPU running current. We did measure the current by PPK to force the CPU always running but the result is quite different...
Dear DevZone, I'm trying to perform a BLE OTA DFU with two nRF52840 Dev Kits. I followed the step by step guide from Nordic provided at the following link: devzone.nordicsemi...
Hi , Dear Nordic supports:
I am using NRF52832 for the iterative development of a product. In the previous generation of products, I used a PWM control LED flashing, whose...
