Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
There is a problem printing the log message. I am using SDK12.3, keil compiler and segger J-Link. After modifying the project a little, normal log output is not available...
Does the nRF9160 have an ATEX component certificate? Why there is no marking such as "Ex ia IIC Ga" provided? What exactly do you understand by the term "ATEX compliance"...
After a conversation with a Nordic engineer and some research it looks like there is no official way to upgrade a product over the air from an nRF5 SDK based product to an...
I ported the Thread Secure DFU example to use FreeRTOS, however I get a hard fault if something is scheduled using the app_timer provided.
Calling coap_dfu_trigger or handling...
We have a custom PCB fitted with the nRF52840 SOC, we've previously erased and written to it via the nRF programmer tool. However, when trying to use the nrfjprog -e command...
Hi. I am having trouble connecting nrf5340 PDK to nRF Connect app on my phone.
I am using the peripheral_uart example based on https://infocenter.nordicsemi.com/index.jsp...
My customer is using a Taiyo Yuden module, EYSLSNZWW, that uses the Nordic nRF52810 chipset. We need to configure the board for Bluetooth Qualification testing. I have read...
Hello,
I use the TP4056 charging module and the 3.7V lithium battery (300mAh) and work on sdk v17.
One of the features I'm trying to create is when the charging connector...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I am trying to test ble_app_blinky_c.
I have problem with received data from peripheral which is my...
Hi,
I am new to the nrf52832 and I wanted to use its Bluetooth functionality for a project I am working on. I have read about the theory behind the Bluetooth stack etc,...
Hi,
Is there any sample Android mobile application available which calls or consume the Temperature/humidity for nrf5_SDK_for_Mesh_v3.2.0 ?
Best Regards,
Hi,.
I am using nRF52832 , sdk 16V
How many samples can be sent over ble if we set 7.5ms minimum
I need to send the 100 samples. I tested by setting to it 7.5ms I think...
H i everyone, I'm having a problem as follows: I am wanting to use LPCOMP to wake up the nrf52840 from system off mode. So can anyone give me an idea of how to do that?
I tried Searching for the NRF_CCM structure, but could not find it.
Where should it be nor the MAXPACKETSIZE.
this code is in the system_nrf52840.h
Also, could you please...
Hi
We are doing field trials of a nRF52840 product with s140 SD, now and again NFC stops working (tag type-4, read and write).
This has been seen in SDK15.3.0 with SD6...
