Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi Dev Team,
I have an iot.1nce.net sim that I am using in Germany.
+CGDCONT: 0,"IP","iot.1nce.net","10.205.84.3",0,0
I was trying the eDRX configuration using a basic...
Hi,
The ' nRF52840 Errata Attachment Anomaly 172 Addendum' linked to in the nRF52840 errata (Version 1.3, page 17) seems to be missing; the link gives a 404 error. Where...
I've tried to test the ZigBee OTA example on the 4.1.0 SDK, but it does not work. I've gone through the exact steps of the procedure as described in the infocenter, but it...
Hello,
in our project we have a nRF52840DK as central (s140) and a custom board with nRF52832 chip as peripheral (s132). The software on the nRF52840DK is based on the ble_app_uart_c...
When I program the Zigbee cli example from T&Z SDK v4.1.0 I see that the Zigbee stack uses some flash areas at the end of the chip. In my case 304 bytes @ 0x000F7000 and 24...
Hello,
Using libuarte I have been able to set up UARTE0 and UARTE1 for main communications, and debug communications respectively. While using UARTE1 to print out debug...
Hi,
I's trying to implement switch two application firmware in the openbootloader example, but I meet some issue.
I change the sector to 0x27000 in App1, 0x40000 in...
Hi, in my app, I have to implement sleep between transmission running at 4Hz. On the background there is running adc, which data are collected via ppi, timer and SPI easy...
When turning off the UART device, the UART ASYNC API callback will be called with the UART_RX_STOPPED event.
This will then not recover, and the event will be spammed infinitely...
Hi.
I am using nRF9160 DK. I want to communicate BLE in series with multiple DKs. Assuming there are DK 1, DK2, DK3... ...DK9, DK 1 is connected to a computer. DK 2 to 9...
I've managed to successfully increase BLE MTU Size and Data Length on a 52840 to 247 and 251 respectively.
This works fine with BLE Notifications on a recent MacBook Pro...
I've reinstalled several times. nRF Connect recognizes PCA10100 at serial COM8 but all the read/write functions are all grayed out
2020-11-02T23:19:35.987Z INFO Application...
Hi All,
trying to understand the USB CDC ACM example for the Nordic 52840 using SDK17. I believe I've got it working, but there's one thing I'm not quite understanding....
Hi,
I am reading some sensor data based on interrupt and i am string the data after read "n" bytes.
my store function takes around 300-400 ms but i have to read samples...
