Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hello,
I am working with the nRF52840 dongle. There is a bootloader at the end of it's flash, which can be started by pushing reset after power up.
However I cannot start...
Hi Gene,
One of my customers using our module to pilot run.
https://static1.squarespace.com/static/561459a2e4b0b39f5cefa12e/t/5da77e178970da0cc270ef0d/1571257883383...
Hello,
I noticed that Table 7.3 of nRF52832_PS_v1.4.pdf states that 37 interrupts have been implemented, whereas the peripheral listing in the documentation as well as interrupt...
While advertising I could see some increased current peaks on one of the three channels. Its random and is observed mostly at the first or last channel of advertising.
Any...
Hi,
I wish to power optimize the proximity example application, as my intention to make a find-me tag. So I may not need the lls and tps services. Is any guidelines for...
Hi There,
I now have 4pcs PCA10056 and 4pcs PCA10059 for the development of our BT Mesh products by nrf52840 of Nirdoc. I have completed the installation of the tool chain...
Hi, I wanted to send data over Bluetooth 5.0 modules and to see on a terminal. So I used nRF52840 DK as central device ( ble_app_uart_c) and Fanstel modules ( ble_app_uart...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
Hello,
background: using Keil IDE, my own board that has a nRF52840 on it. My goal is to create automatic DMA transfers from SPIM3 peripheral.
I am setting up EasyDMA...
I'm porting a working app from SDK 1.1 to 1.2, and have noted that when I make an mqtt connection close it, and re-open (to a different mqtt server) that the call to nrf_connect...
