I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
Hi, recently I have been experimenting with the channel sounding with range requestor sample on the nrf54l15dk. I have modified the reflector code to make it connect with...
HI
I'm writing a programm the using a nus as its service, because nus is a custom service there is something that need to be changed, I followed the tutorial about making...
Objective: I want to read 64MB data stored in external flash (interfaced with nrf52840) from android mobile App (specific: One Plus 7T)
SDK: nRF5 SDK v16.0.0
Soft Device...
Dear,
Im trying to measure the RSSI with THINGY:91, I found on the document nrf91_at_commands_v1.1.pdf about
1. AT+CSQ
+CSQ: <rssi>,<ber>
Note: Not detectable, RAT...
Hi!
I am currently working on a project where i would like to use Thingy:91 as MCU board as it contains other features i need to use, like 4G and GPS.
The problem is that...
Hi I'm currently develop new product based on RAK8212. I have problem with reprogramming devices. Programmer i use is nRF52-DK I'm not able to reprogram about 10% of devices...
Hello,
I have a low power application, which is activated by a push button press. (The DC-DC converter is also in shutdown mode normally, so the NRF9160 does not have power...
I am occasionally (very rarely) getting "Mesh assert at 0x00037996", but when I try to look this up, I get:
My understanding is that this means the mesh_assert is...
Hello, this is the nrf52833/52820 design drawn by the customer, because this is our first contact, please help to check whether it is reasonable? thank you.
Hello,
I'm working on a BLE app on an Arduino Nano 33 BLE, which is equiped with an nrf52840. I'm struggling to increase my BLE transfer speed ( i think due to the limitations...
Actually i was working on 3 boards, nRF51422,nRF51822 & nRF52840. While executing some examples on each board i realised that each board has its specific pca hex file to be...
I n the main of my program I have this( UBLOX_PWR_PIN = Pin16 of nrf ),
uart_init(); nrf_gpio_cfg_output(UBLOX_PWR_PIN); nrf_gpio_pin_set(UBLOX_PWR_PIN); nrf_delay_ms(200...
Hello,
I've a problem with a PPK board.
When the current go over 10mA the value reported is wrong, in my case should be 15mA and PPK measure 80mA and more. Instead, in...
Hello,
I am working on a project that is using nrf52840 chip as a peripheral and the product is supposed to last and run for 25 years. During that period the device will...
Hi everyone I have been reading the GPS data using nordic nrf52840 over the UART. I am able to receive as much as 64KB of data via the UART. Here's the scenario of whats been...
Hi All:
Applyed the under timeslot :
causes some peripherals(eg:static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(2)) n o access interrupt,
what 's the...
