nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
I am studying to use the nRF2460 or wireless digital audio streaming where one Tx broadcasts and several receivers listen and follow. I have the following questions: Can an...
Hi,
How can I read out a vendor model in the NRFMesh app? When I change the model ID to e.g 0x9000, I cannot see the model under elements anymore. Needs there to be any...
I have a list of characters and trying to put them in a string.
char line[13]; /* Line buffer */
NRF_LOG_INFO("Playlist : %c", line[0]); this works displaying 1 character...
We are currently evaluating the two development kits of nrf91 - On the nordic Thingy with Fractus antenna we get the nrf91 into the mobile network after about 20 seconds ...
I know this may be a duplicate of this: https://devzone.nordicsemi.com/f/nordic-q-a/37732/nrf52840-spi-clock-line-contention-causing-spi-driver-to-hang/145521#145521
I say...
Hi,
My working environment:
NCS folder Tag:v1.2.0
J-Link version : v6.62a
SES version:4.42a
test sample code:\NCS\nrf\samples\nrf9160\cloud_client
nrf connect...
I generated two packages for OTA. The first package contains a bootloader and a softdevice 7.3.0. The second one contains a bootloader and a softdevice 8.0.0. I flash the...
Hello,
I want to interface nRF9160dk with ICM20648 sensor using SPI communication protocol. I tested SPI on nRF91 and it is working fine. But how to use ICM20648 with nRF91...
[Embedded World 2020] Failed update of the Thingy 91 Certificate after downloading from the nrf cloud
I Just tried to update the certificate from the NRF Cloud ( https...
https://github.com/NordicPlayground/nrf5-calendar-example
What is lowest power mode where real time clock could run?
How could retain RTC value during reset?
Thanks
