I am trying to setup SPI00 as SPI slave on nrf54l15 but not work as expected.
My board configure is like
and c program like
The program intends to use nrf54L15...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello,
I’m using keil compiler.
My configurations are nrf51822ac/SDK12.3/s130_nrf51_2.0.1_softdevice.
I’m trying to migrate to SEGGER studio.
I’m referring to the...
In my case, I have 50+ devices as sensor and advertising measurements every 10 seconds, ADV_DURATION = 120s, use the 1E FF manufacturer data and self defined payload protocol...
i want to implement the nfc connection of pairing the nordic nrf52840 using SDK ver 15.0.0.
Can anyone help me in implementing this feature? because I'm new to this pairing...
Hello, all
I would like to ask about flash memory write errors.
When using version 12.1.0 of sdk, I was able to r/w to flash memory normally by using the sd_flash_write...
Based on sdk12.3, use 51-dk (51822) to run the ble_app_hrs routine. Use ios mobile phone to connect the device, it will automatically disconnect after 30 minutes, the disconnection...
The problem is not being able to connect to the device from an iPhone SE while the app is in background mode. We have an iOS app written in swift, which uploads data from...
Hello, I have couple of NRF52840 devices that i purchased from Adafruit. I wanted to use them with Alexa Gadgets Toolkit via BLE, however with no previous experience with...
Hi,
I'm working on building a zigbee multisensor device using a nrf52840 module. I'm heavily relying on the multi sensor example and so far I've been able to add temperature...
Is there a way to log bluetooth messages in the phone app? I have a bunch of messages that come but there is no history on the app that I can look at. Is there a to do this...
Hi,
I am working on a project to help determine the distance between the NRF52840 DK and other bluetooth devices using BLE. When the distance is past a certain threshold...
I am currently using the ble_app_uart example but I want to add USB and I2C interface to this solution. Would I need to find what files differ/need to be added from USB and...
Dear Nordic.
We are using NRF52832. According to Mesh spec, It can send up to 380 bytes, So I sent Mesh Data(PAYLOAD) up to 380 bytes. It was successful, but the data was...
When I compiled your sample Bluetooth: Central UART from both master and v1.3-branch branches for nRF5340 PDK (network core has Bluetooth: HCI RPMsg firmware) and I use a...
I initially loaded blinky program in pca10059 using nrfconnect, everything is perfectly working ,
later I have to work in openthead cli uart for which I changed uart pin...
