I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hello,
I am trying to PCA10040 example project program to NRF52810 BLE module.
I just know that the 52810 has different(small) memory with respect to the 52832.
So,...
I have compiled ble_app_blinky sample code from nRF5_SDK_17.0.2_d674dde SDK and loaded it with s132_nrf52_7.2.0_softdevice.hex in my nrf52382 board. I can discover this device...
Hello,
I want to use a Li-Po battery with my nRF52833 development kit and I can't find the specific name of the J6 connector in the DK documentation. Does anyone know...
Hello ! I am working on the asset tracker project on NCS 1.4.0. Since I switched to this NCS, I have an error that comes up very often (once in two or once in three): get...
Online rajAsthana a few seconds ago in reply to Einar Thorsrud
Hi Einar,
Now I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as...
Hi,
I using nrf52832 evk board and sdk17(S132). I want to add the internal temperature sensor reading to the ble_app_buttonless_dfu_pca100400_s132 code present in the examples...
Hi,
1st time using nRF52840 - EV-BT840 on Keil V5.25.20
I use SDK 1702, reference to example examples\dfu\secure_bootloader\pca10056_s140_ble
My question is what softdevice...
Hey,
I have isnstalled ncs v1.3.1 and the toolchain specified in the instructions ofr 1.3.1.
I am trying to utlise the date-time library in the https_client example. ...
Hi Great Nordic Support Team:
Our clients are developing products with 『 nrf52840-WLCSP』. And they find out that there are some mis-information on the spec.
It's described...
Hi,
Dear nordic friend,I am trying to download NCS1.31 by using toolchain manager,but it work bad,show in below.
I have use some ways，to make me can visit the web in Europe...
Hi, I'm having difficulties driving SDOUT when it's configured to pin 19 on the NRF52840. I can operate the peripheral and see output data when my WS2812_PIN macro is assigned...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
Hello everyone,
I'm programming nRF52833 for my own application. In my application, I have a button to turn on and turn off the supplier. There is only 1 button so that...
