The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi There
I am debugging my application board by light-swtich server project of Mesh example and " pca10056_s140_ble_debug " project of SDK example dfu.
My application...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
Like the subject, I'd like to change 'ble_app_hrs_c' and connect it to my device.
I changed the service...
Hello,
I am running an application on nrf52840DK. It is using uart service to send a sensor data through BLE to Uart servic on smartphone. I want to measure the current...
Hello,
We just noticed that according to the Raw data detail in nRF Connect, we are able to advertise more than 31B data limit. Is that possible or do we incorrectly count...
Hello,
I am trying to figure out a way to configure the adc node using the .dts Device Tree file in a similar way to what is done for other nodes such as &spi and &i2c....
I've installed the nRF Connect SDK Master manually since I need the Zephyr modules for a school project. I've manually installed the SDK before without issues but on my new...
Hi Dev team,
I am working with a nRF9160DK board. I am currently getting an error while building my SPM folder in : C:\Users\adeel\ncs\v1.3.0\nrf\samples\nrf9160\spm.
...
Hello!
I'am from austria and try to connect a Thingy:91 to your nrf-Cloud. First I tried it with your
iBASIS sim-card, but in austria we can't use this card.
Then I...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
When using the serial_lte_modem application on a custom nrf9160 board I have discovered that I get nothing out of the UART unless I pull VEN low and then release it (reset...
