In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Dear All,
I am using the ble_app_template as my baseline. I have created a custom service with various characteristics and I am able to broadcast my service, connect and...
Our compliance engineers are failing the unmodulated FCC test for our radio because the signal only spans 1MHz, but needs to span 2MHz. We do not have this issue when using...
Hello all,
I'm working on a prototype for a device that simultaneously scans and advertises in certain cases. I have been able to do everything so far except scan by copying...
Hi
I am working with nrf52832 NORDIC soc with Segger with nrf52 sdk 16
I have looked at the "pin_change_int_pca_10040" example and tried to play with it a little bit...
Hi there,
I recently upgraded to nRF Connect for Desktop v3.3.3 and the programmer module to v1.4.2 and I am experiencing the following issues. At first, when I would try...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
I am using nRF52832, And SDK 15.3, the ble_app_blinky project,
a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project,...
Setup and goal: I'm developing an BLE central app and would like to use scan address filtering to find a specific device. I enabled the filter and provided a hard-coded BD...
