I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
In the nRF5340, is the application processor able to run concurrently when BLE transactions are happening?
In previous generations of the nRF family, the application stalled...
Hi everyone,
I am trying to understand the GATTS Handle Value Notification diagram.
From what I have understand so far is tha the soft device keeps a buffer (ATT table...
Hi engineers,
I want to implement function that input i2s data and then output it directly.
I find that i2s demo includes two buffers which are used for current buffer...
Hi,
I want to verify
1. Program ble_app_hrs with buttonless dfu integrated + secure bootloader + bootloader setting to nRF52DK.
2. Boot up nRF52DK, then use buttonless...
I don't know what happened to my thingy 52 after lots of firmware updates with Keil+Jlink+thingysdkv210 and nRF connect operations. The LED on thingy isn't flashing any more...
Hi engineers,
I want to use saadc to measure the battery's voltage, but the result I get is incorrect.
So I use the saadc demo of the nrf5_sdk17, then I measure GND(negative...
Hi. I am trying to use PIN 0.19 as my SPI CLK but it is always low.
Previously, I tried to change the pin to 0.26 and it works.
Is there any other configuration required...
Hi Nordic
SInce this is my first time to develop Nordic chip and implement SPIS driver, Therefore i am not so familiar with Nordic API. I would really appreciate it if...
HI,
I want to upgrade the BL in APP directly. I encouter a wierd problem. When APP erase a specific page of the BL(the address is 0x74000), the system halts. If ignoring...
Hello,
I am using nrf51822/SDK 12.3/sd 130.
An error occurred while implementing nus_c using multi-role example.
Error 7 occurs in sd_ble_gap_conn_param_update() frequently...
Hi,
I used Jlink Edu successfully to flash the asset tracker code using segger. but when put the breakpoint it went to some different file.
I have a quick question regarding...
I have just received an nRF52833-DK and am trying to get started with it.
I am at the website:
https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52833...
Hi,
I press Button 1 and Reset to put the nRF52840 DK in to DFU mode that is programmed with a immutable bootloader (B0), mcuboot, and application. This works well to...
Hey. I am new to this forum and new to programming BLE chips. I have ordered my first dev board and cant wait to get my hands on it. I have been reading a lot for the coupe...
Guys,
I am currently experimenting with an existing wearable that contains an NRF52832XXAA Revision 1, and I'm having a hard time to have it running a simple BLE peripheral...
