Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
How could I rebuild the code for an NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION?
static void ble_stack_init(void)
{
uint32_t err_code;
nrf_clock_lf_cfg_t clock_lf_cfg...
Using Mesh V.4.0 and Stack 16.0.0
I have created simple message model in light_switch _client code.All I want to do is call status = simple_message_client_set(&m_clients...
Hi,
I have a simple question. How should I handle situation, when need to collect data and process them before the computed data are sended via ANT+ profile which runs on...
Hi,
I'm working with the nrf5340 and I'm trying to perform a FOTA upgrade over BLE. After initiating DFU with nrf Connect for Mobile the process crashes right after...
Hello,
I'm working on a HID BLE device and it seems to work good with iOS devices. It fails to pair with Window. I'm adding what I can see with the sniffer. Basically after...
I am read the datasheet of vl53l1x ,can anybody help on connection of vl53l1x to nrf52832 and how to use sensor vl53l1x ....any driver code for vl53l1x sensor
I want driver...
I have the following trivial program which has almost identical functionality to the connectivity/ble_connectivity/pca10040e example:
int main(void) { uint32_t err_code...
Hello,
I interfaced nRF9160 and SD card using SPI. I started with this sample: ncs/zephyr/samples/subsys/fs/fat_fs.
Now once the files from SD card are read, I want to...
Hi, I've began making a SPI module for programming a PIC16. It only transmits data, so two pins. My questions are: 1. any obvious errors? 2. does the EVENTS_ENDTX occur when...
Hello everyone
I have an question when I used the 52832.
First of all,I configed "nrf_drv_spi_init(&spi, &spi_config, spi_event_handler, NULL);" and the file (nrf_drv_spi...
We are about to use the nRF52832 and are looking at which SofDevice to select for a Central-only implementation. The S122 summary says it targets the nRF52820 and nRF52833...
i m using NRF52840 with sdk 15.2. In that i m testing direct test mode by UART.Now i can do transmit mode.i can check through nrfconnect dtm mode. i cannot check receiver...
Hi,
I tried the following AT settings on the nRF9160 DK board:
AT+CPSMS=1,,,"00111000","00011110"
AT+CFUN=1
After this the modem enters PSM mode and the current is...
Hi,
One of our modules using PCA10090 0.8.2 programming and production nRF9160/nRF52840 modules.
Our customer reported that they can't use PCA10090 0.9.0 re-programming...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
