Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
When using the serial_lte_modem application on a custom nrf9160 board I have discovered that I get nothing out of the UART unless I pull VEN low and then release it (reset...
Hi guys,
I am using Zephyr RTOS and trying to enable my device to send the voltage data via BLE. I use two nRF52832 boards, one of them is peripheral for which I use peripheral_ht...
Hi Team,
We need to know the what kind of security level available in Nordic nRF52X(nRF52833).
Secure boot support and where the 128bit AES keys are stored and accessed...
Hi Team,
We are going to use nRF52833 chip-set and we need the below information based on this input we will decide our chip-set.Kindly update your support.
1. What is...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
Hello,
I read through the datasheet of the nRF85832 to understand the peripherals a little bit better, but I got stuck while looking through the register overview (in this...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
Hi all,
I'm working on a project which I started from the multiperipheral example. I am using SDK 15.3.0 for this. I am developing the software on the nrf52840 DK using...
Start SEGGER Embedded Studio by clicking Open IDE //Successfully installed, what means Open IDE ? ? ?
Select File → Open nRF Connect SDK Project… //it just dont appear in...
Hi,
Currently, I am in a feasibility analysis stage for an application which requires BLE Mesh with Localization (RTLS using AoA and AoD). I explored SDKs for nRF52833...
Hello,
on SDK16, with nrd52dk, with android phone, standard ble_app_uart example works fine with nRF Toolbox. But when I disconnect from nrf52dk, the chip still thinks the...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I changed the device name while not connected.
but, The...
