I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
i am using nrf52840 dongle with uart using ble_app_interactive example,
but after commenting only uart with cli is replying with some text as shown in image .
For the...
Hi! I'm using S140 and I'm using the ble_advertising module to set up advertising.
This is my advertising_init function which is working properly until I uncomment the enabling...
This is perhaps not so much a question as a request.
The FDS event handler, type `fds_cb_t`, has only one argument, type `fds_evt_t`, unlike (say) the two wire event handler...
Hello,
I would like someone to explain to me payload for Zigbee cluster library (Zcl)
i was following this guide to control my lights:
https://infocenter.nordicsemi...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
hi... i want to store data in flash , i will get the data periodically . i have merged the ble_app_uart +fstorage example . Even i am writing data to flash using write command...
Hi everyone, I have a question related to the power supply of nRF52840 DK
I want to operate the nRF52840 DK with a LiPo battery (for experimental purposes). Is it possible...
The antenna is mechanically symmetric, but as I understand not electrically symmetric.
Is this an errror ?
www.fractusantennas.com/.../UM_FR01-S4-210.pdf
Chapter 5:...
I am wondering what happens to the NRF LOG statements when not running in the debugger.
I have found (probably due to interaction with the SoftDevice) that too much NRF_DEBUG...
I cannot get the scope of the sdk_config.h file to encompass all modules. Process
Start with example project using the file system as per the install.
After compiling...
I would like to use the UART at the lowest possible level and Ihave created a very simple example which uses the UART bus with the registers. The example should write word...
Radio is flashing green, on and off, but I can't seem to connect to it. Looking at the graph of usage, I can see that it is talking to something since the available amount...
Hi,
I'm using pc-ble-driver-py.
I bought the nrf52832 dongle.
The problem is uart pin number of dongle.
The pins of my dongle and the pins of the hex file are different...
I am working on adding firmware updates to my BLE application on the BL652 module ( nRF52832/PCA10040 ). nRF 15.2.
I added in the code for the BLE Background DFU, which...
Hi ,
I can not understand or there is something wrong in this example here ;
He defined " point_fifo" but initialized "my_fifo" , How does this work ?
https://infocenter...
