I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Dear Support,
i'm testing PCA10040 board. I'm using nRF5_SDK_15.3.0_59ac345 SDK package.
I'm testing the project ble_app_hts. I compile it and i download the firmware...
The download page for nRF52840 DK ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-DK/Download#infotabs ) has download links for Heart Rate Monitor...
Hi DevZone,
I am new to nRF SoC and SEGGER. After installing all tools, I can build and run examples.
I run into a problem to add and enable a nRF driver, like "UARTE...
Hello, I am trying to develop a rehabilitation exercise service using Thingy52.
Thingy52 is the only device to accomplish my objective which needs motion detection using...
Hi,
I have nrf52840 DK and PCA63511 Power Profiler.
I have two questions:
1. The Average Current Consumption measured with profiler is 110uA (18 mA max, over 10 s...
Hi,
I have Raspberry pi board which i want to use it as a gateway .on which server will get set up.
nrf52840 will be the beacons which i have already set up for sending...
I am trying to use the NRF connect mobile app on android 8.1.0 to try and connect to a Bluetooth server serving GATT request to verify functionality.
The server is running...
Hello,
I am using these pre certified modules https://www.nicerf.com/product_147_88.html in a project which is basically nrf24l01+ with a PA and LNA.
These support ...
Hi,
Just been testing the data rate of write without response commands, I'm only getting about 250 bytes / second which seems incredibly slow?
I've just got a simple little...
Hi,
Is it possible to route an analoge signal through a digital GPIO pin to access the inner analoge pins of a nRF52840? I want to avoid using via-in-pad to keep the cost...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
I have made changes from here in order to configure data rate at Coded PHY for mesh application.
Tested with two phones: Moto G5 Plus (Bluetooth 4.2) OnePlus 6 (Bluetooth...
Hi,
I am tring to display some information using NRF_LOG_HEXDUMP_DEBUG(). However, I can't see anything on the terminal. If I use NRF_LOG_INFO("xxxxx"), I can see the...
