I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
I have an embedded Linux platform which uses an nRF9160 connected via UART. The nRF9160 has been loaded with the serial LTE modem firmware, version 1.3.1.
I've been experimenting...
Hi!
I'm developing the NRF9160 target from a raspberry Pi. The problem is that I need occasionally to perform modem firmware upgrade, and I can't figure out how to do it...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
I have add a custom characteristic in the heart rate service sample code.
The characteristic is shown on...
Hi Nordic,
I am using your official board nrf52840 to develop my application based on the ble_app_uart_peripheral example. BLE communication and the spi interfaced sensor...
Hi, I'm working with a nordic thingy:52 and SDK thingylib on Android.
The issue I'm facing is that the real sampling frequency, compared to the one indicated by the SDK...
Hello,
I try to use the ASSET_TRACKER application with NB-IoT/ Vodafone in Netherland. Vodafone uses UDP/IP datagrams protocol. is it possible to modify the asset-tracker...
So, we are using NRF52811 with external 32MHz xtal and also exeternal RTC crystal.
Every now and then we are unable to pass tests of the programmed firmware because the...
Dear Sir/Madam,
I have already developed an RF communication device with an NRF24L01+ device. And I want to migrate to nRF52833-QIAA-R. For that, I have the below questions...
I'm using RTC to wakeup every 500ms, I have Watchdog enabled but after a while (about half.. or an hour...) it will not wakeup anymore and watchdog will not reset.
I measured...
Hi, we programmed the nRF52840-DK with ble_app_hids_keyboard demo (s140) and tested with different BLE keys under a Linux PC. It worked. Tested the same configuration with...
Hi,
I have some code that normally uses nrf_crypto with the cc310 or cc310_bl backend. I was writing a unit test for this code which compiles and runs in Linux/WSL. Since...
Has anyone written a utility to dump the tables of contents (i.e. directory of files) and
an entire file with record keys:contents to a host operating system file to a file...
Hi,
I'm working on the bootloader part of a project. Using nrf Connect, the integrated MCUBoot bootloader, trying to figure out how all the parts fit together. Running into...
Hi,
As iOS developer, I'm facing a really strange issue : Using the nRF Connect app, I try to connect my BLE device, with success or not depending my iPhone/iPad configuration;...
Hi guys,
I am using the nRF52832 board on which I run the LPN example from BLE Mesh directory. I put there the code for measuring the temperature and now I want to save...
