We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
Hello,
We have a product that sends out an ESB message approximately ever second, it does this using the RTC timer with the following setting:
It sends the message...
We want to add the nRF52805 to an existing product but also want to have the option to perform a firmware update.
The current DFU implementation doesn't allow the softdevice...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
Hello,
The Power Profiler Kit(PPK) is not able to measure current consumption. I got this notification asking to reprogrammed the device, I clicked yes and then-after it...
Hi All,
I am currently in the process of designing the PAB layout for my design. My schematic follows the reference design 4 recommended by Nordic.
In this VDD_HV (From...
Device: nRF52832
SoftDevice: S132, 7.0.1
SDK: 16.0.0
I want change DEVICE_NAME by nRF Connect APP, then I add below code, but I found it die here "wait_for_flash_ready...
Hi everyone,
I am working on a project where I have to enter the system into System OFF mode and RAM retention. What I actually want is to retain the value of some variables...
