Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
May I know what is the difference of three PNs NRF51822-QFAA-R (H0) AND NRF51822-QFAA-R (G0) AND NRF51822-QFAA-R?
How to identy the three PNs? May I know if NRF51822-QFAA...
I am trying to implement a scenario where the system will be sleeping for a mentioned period of time and then wake up and advertise and transfer data over BLE.
I am using...
Again, if the search engine in your documentation were decent, I would probably not need to ask this question here. The answer probably exists, but try an find it not knowing...
Hello Nordic lovers,
Happy Merry Christmas.
In ble_uart code, I'm interfacing the FreeRTOS & twi_sensor code
The program executed without any error.
And it starts...
Dear Members,
How can I wake up the chip without a button
I'm using the example for Ant,
Ant_bsc_rx .
I have disabled the button with :
bsp_init(BSP_INIT_LEDS...
Hello and Merry Christmas,
Trying to get Thingy:91 connected to cloud. But no such luck.
Followed the video, but somethings are shown. Installed latest firmware (SIP modem...
Hello
I have two questions. Your thoughtful response will be appreciated.
1) What's the impact on power consumption with 1 Mbps vs 500 kbps vs 125 kbps for the same amount...
Is there any way to leave the PPK 2 output enabled when I leave the Power Profiler app? If not, then can I submit this as a feature request?
Without this option I have to...
1、Does Nordic 5340 support 1443a protocol；
2、When the chip（5340） is not powered, does NFC function support passive swiping card
3、Can the reading distance of NFC be more...
Hello
I am using the APII described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/modem_key_mgmt.html
to add keys to the modem...
Why does the nRF9160 Tx power fall far short of the specification? Its seem to be a false claim that the nRF9160 is a 23 dBm device, and rather is a 20 dBm device. In other...
In the flash write example code the very start of main.c has the following lines
The comment says "Use last page in flash". However, what I am guessing from the code itself...
I am trying to use nrf_serial with IRQ. Tx operations just fine but, i can not get any interrupt when a data comes from uart. I am using sdk 14.2 and not using ble.
Hi,
I am using SDK 14.2 and made some changes with serial example in the SDK. It works just fine while debugging but outside of debugging does not work at all.
I have...
