Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Dear all,
I am interested in a BT mesh modules that support precise time synchronization between the modules (microseconds). This is required for sensors application that...
Hi,
I installed nrf Connect SDK 1.2.0 using the nRF Connect 3.3.2 App - Toolchain Manager. (Windows 10)
Using SES for Nordic v4.52, I opened the asset tracker project...
Is there any way I can scan for a short period of time with a duplicate filter on so that I only get 1 packet form the advertising device in one scan window.
For example...
I recently purchased and downloaded the nRF9160DK. The DK User Guide v0.7 does not match the Altium design files schematics and neither match the application schematic in...
I have project with nrf52832.
every second, i want send 11k byte data from nrf52832 to android app, but it is loss data. (i used phone ble 4.2 loss about 1-2% packet)
...
Hi,
Been starting to program the thingy91 and faced some issues. This is the second attempt after failing on the PC and now using the MAC.
Managed to follow the steps...
Hi Sir,
I use the example ble_app_uart_c, the program runs to APP_UART_FIFO_INIT() in uart_init(), an error will occur, and the program jumps to NRF_BREAKPOINT_COND -->...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
Hi, Im new here and microcontroller programming... I curently waiting nrf52840 PDK so Im only quick read SDK and documentation... Before Im program only devices with .NET...
Hi, I cannot open my project using SDK v1.3.0 (nrf9160dk_nrf9160ns selected board) I installed the v1.3.0 using nRF Connect v3.4.1 - Toolchain Manager I already downloaded...
Dear Nordic: I have issue about connect handle. My product supports 1 peripheral and 3 central roles. 1. For this configration, i am not sure handle 0 is resverd for peripheral...
Dear all, I have a question about IV index and sequence number in mesh network. If i have 3 nodes success provisioned. I will only power on 2 active node ( node 1 and node...
Can't see why this is occurring. I've checked my custom board and the reflow of the chip under microscope. The doc indicates this pin isn't linked to a peripheral. Despite...
I am using Nordic board to drive an accelarator. There is already an exist project and it can run successfully. I want to combine this project to a new project and it has...
