I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
I just trying log via Segger RTT viewer, followed the the same procedure as that of serial_lte_modem sample in my new project and could not see logs showing in the viewer...
I am working with nRF52 DK, SES4.30 and SDK 15.3 with SD 132.
This error just started occurring once I set up app_timers. My code for setting up my timers is below:
...
Hello,
I ordered a nRF5340-PDK board and i'm trying to get it to work.
When flashing the Heart Rate hex file I couldn't find the device (i pushed the reset button)....
I am using SDK 15.3, SES 4.30 and softdevice 132 with the ble_app_uart_c as the core functionality for my system.
I've read many dev support threads about this issue and...
hi... I am working on nRF52832 . nRF52832 ,RX TX is connected to the esp8266 of tx,rx . i want to send the data from nRF52832 TO ESP8266 via uart . which function can i use...
I'm running the ble_peripheral\ble_app_uart example on my nrf52832, it works great.
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART" /**< Name...
Nordic Support,
I came across the following thread that says that SWO is not supported on the nRF9160:
https://devzone.nordicsemi.com/f/nordic-q-a/56098/is-swo-on-nrf9160...
https://devzone.nordicsemi.com/cfs-file/__key/communityserver-discussions-components-files/4/ADXL375_5F00_I2C.zip
i was using the code from above link
my sdk is 16
when...
Hi,
I am testing NFC on the nRF52840 preview kit that I have (PCA10056, v0.9.2) using the included NFC antenna. I am running the pre-compiled examples from the 16.0.0 SDK...
Hi
My company is currently using nrf52810 for a tracking application, but I see there're some new features on your nrf52811 iteration, as phased-array aperture and thread...
Hi!
I'd like to get a minimal "Hello World" example working for data transfer over 802.15.4
I have two of Makerdiary nRF52840 MDK USB Dongle, one as sender and one as...
Dear all,
I'm using nRF52810 with nRF5_SDK_16.0.0_98a08e2 and s112_nrf52_7.0.1_softdevice
I've implemented a custom service which exposes 4 characteristics.
2 of them...
Hi, I am trying to build ADXL362 with pca10090ns for nrf9160DK (PCA10090) (west build -b nrf9160_pca10090ns). I have added the following configurations in prj.conf. Though...
Hi teams,
During development, I need quite a long period timer for hours.
Searching for the subject, I found application timer can only handle few minutes because of 24bit...
