I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hello ,
Now I am sending the data per 7.5ms in the interval of time over ble .I am loosing the packets , to avoid this I am planning to send the data in the structure .How...
Hi,
I got a unit based on NRF52 (No matter what SDK) which is connected via 1-wire (dallas protocol which is very time accurate) to other unit.
The other unit is the master...
Hi! I wanted to ask someone who knows more than I, if this setup makes sense, and how I could test my design.
A bit of background: We're developing a custom board which...
Hello, I am using nrf51822 / SDK 12.3 / SD 130-2.0.1.
When a normal timer is set and softdevice off, the timer interrupt does not occur.
In SDK 10 / SD 110-8.0.0, timer...
Hello,
I am trying to use the flash API of fstorage in my code. I have called below function at the start of my code. I want to save some integer values every 1 min interval...
Hello
I am trying to read a characteristics from my peripheral using my central. From what I read here, I have to use sd_ble_gattc_read(). Is it correct ? But I did not...
Hello
We have produced boards with a Telit module using the nRF52832 chip.
Our software developper have a lot of problems making the connexion and communication reliable...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
Hello.I am a graduate student at Nanjing University of Posts and Telecommunications in China.My question is, does your company provide the source code of the Bluetooth mesh...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
I am not able to run commands with nrfjprog using the J-link Segger device
e.g. nrfjprog --family nrf52
I can do it only with the Keil or Segger UI environment
How can...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
Hello
I am working on SDK v17, using nRF52832 (MDBT42Q) and MPU6050 sensor. I tried TWI_SCANNER because I thought there was a problem getting the value of MPU6050.
However...
I am reading a thermistor voltage divider from Vdd using the SAADC with a reference voltage of Vdd/4 and gain of 1/4. I thought that this would track Vdd so I wouldn't need...
