here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
I am using a nRF DK (nRF52832 - PCA10040 - SDK 15) to communicate with a custom electronic device developed by my own company (which integrates an 1-Wire slave)....
Hello,
I have a question regarding eDRX mode on the nrf9160 in combination with NB-IoT. I tried to configure an eDRX cycle of 20.48s for the use in a battery powered actor...
Hello,
I am using the nRF52832 on a custom board, with SDK 15.2 and SD132 v6.1. My BLE application uses the SAADC to measure VCC voltage every 6 hours. I am using an app...
Hello Sir,
I am Working with nRF52 DK Development board. My application based on BLE. I want BLE stack for Scanning mode and also tell m,e how to operate with mobile apk...
How to
1. increase advertising frequency - Which BLE GAP parameter should be updated?
2. increase RSSI signal strength - My device is not battery operated, so there are...
Hi,
How can I make the modem start a hot fix after rebooting the nrf9160?
I am getting a GPS fix, then powering down the modem with CFUN=0, which should be saving the...
Hello, I recently bought a nRF52840 with the intention of using it as a substitute for UART wired communication. What I want to do is send and receive messages between my...
I carried out following steps:
Application was using SDK 11.0.0 for nRF51 SoC
Ported SDK version 12.1.0
Using secure DFU boot-loader from SDK 12.1.0 (followed all...
Hi,
I understand I shouldn't use S140 v6.1.1 with SDK v17.0.0, but we want to try to keep using v6.1.1 as it's been well tested. Since the ATT_MTU example works with this...
Hi, im trying to gather accelerometer data from Mi Band 3.
I found script, written in python, that allows computer with linux to connect to band. But its missing functionality...
hello all,
I am referring ble_app_hts code for development. and I need to add saadc code in my project.
app_timer is used in ble_app_hts code & nrf_drv_timer is used...
Hi,
I have one custom board based on imx6ull, which has nrf52840 embedded on it. Both communicates over serial/UART.
On host side I'm using linux Bluez stack v5.50 and...
Hi,
I am new to BLE Mesh development using Nordic.
I am trying to write a python script for mesh provisioning an configuration using Serial Interface.
when I am launching...
Hi all,
I am working on a project with an Adafruit ItsyBitsy that uses and nRF52840 chip, and I am having a bit of trouble with getting the timers to work accurately....
I currently have a device running on sdk15 with a softdevice 6.0.0. I got a bootloader running the DFU code, and updating the main image works perfect. We load a default image...
