Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear all,
I am interested in a BT mesh modules that support precise time synchronization between the modules (microseconds). This is required for sensors application that...
Hi,
I installed nrf Connect SDK 1.2.0 using the nRF Connect 3.3.2 App - Toolchain Manager. (Windows 10)
Using SES for Nordic v4.52, I opened the asset tracker project...
Is there any way I can scan for a short period of time with a duplicate filter on so that I only get 1 packet form the advertising device in one scan window.
For example...
I recently purchased and downloaded the nRF9160DK. The DK User Guide v0.7 does not match the Altium design files schematics and neither match the application schematic in...
I have project with nrf52832.
every second, i want send 11k byte data from nrf52832 to android app, but it is loss data. (i used phone ble 4.2 loss about 1-2% packet)
...
Hi,
Been starting to program the thingy91 and faced some issues. This is the second attempt after failing on the PC and now using the MAC.
Managed to follow the steps...
Hi Sir,
I use the example ble_app_uart_c, the program runs to APP_UART_FIFO_INIT() in uart_init(), an error will occur, and the program jumps to NRF_BREAKPOINT_COND -->...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
Hi, Im new here and microcontroller programming... I curently waiting nrf52840 PDK so Im only quick read SDK and documentation... Before Im program only devices with .NET...
Hi, I cannot open my project using SDK v1.3.0 (nrf9160dk_nrf9160ns selected board) I installed the v1.3.0 using nRF Connect v3.4.1 - Toolchain Manager I already downloaded...
Dear Nordic: I have issue about connect handle. My product supports 1 peripheral and 3 central roles. 1. For this configration, i am not sure handle 0 is resverd for peripheral...
Dear all, I have a question about IV index and sequence number in mesh network. If i have 3 nodes success provisioned. I will only power on 2 active node ( node 1 and node...
Can't see why this is occurring. I've checked my custom board and the reflow of the chip under microscope. The doc indicates this pin isn't linked to a peripheral. Despite...
I am using Nordic board to drive an accelarator. There is already an exist project and it can run successfully. I want to combine this project to a new project and it has...
