Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi.....
I get the following error fault from my device (nrf 52840 with freertos ,using SDK16.0)
the Fatal id: 0x2000B730
what caused Fatal id: 0x2000B730 ?
Hello,
I developed a project based on thread CLI example. Everything works fine but I would like to add more commands to the CLI interface, maintaining the existing Thread...
Hello:
I am using nRF Connect v3.3.1 programmer to flash nRF9160 and got an error.
Silk on nRF9160 is: nRF9160 SICA B0 191601
Programmer can't recognize nRF9160 after...
Based on 52832, sdk15.3 running ble_app_hrs example, requesting MTU through nRF connect, the first success, the second time is unsuccessful, the app prompts Error 4 (0x4)...
Is there an application note or single set of instructions on how to get debug/log output via the SWO output rather than RTT or UART. Both of the latter are simple switches...
I'm trying to hook up a nRF51 to two other devices. One is connected with UART and the other through BLE (NUS).
The connection with BLE is working fine. But as soon as...
I am using "ble_app_hrs_rscs_relay" example. I am not able to set the TX power of advertising and scanning both. Currently the avg current is too high.
I also tried using...
Hello, in my travels through Nordic development, somehow I am only now creating truly custom characteristics, and I realize I have no idea why there is both an initial and...
Hello, when I run the subject example and connect to it, I see the RX and TX characteristics like I'd expect.
However, I see a descriptor on the TX characteristic which...
Hello! I am trying ZigBee multi_sensor example.
(I had a question here as well. Thank you. "Zigbee multi_sensor example has not connect" https://devzone.nordicsemi.com...
I want to set up a SPI transfer so the transfer itself is triggered by PPI. The PPI is set up working, the chain of events is
Timer CC0 -> Set CS low
Timer CC1 -> Start...
In implementing the --application-version-string with nrfutil I found the help was inconsistent with the application.
The help for this option is:
In the example 2.7...
Hi guys.
I'm trying to merge two projects ble_app_beacon and nrf_crypto_aes_cbc_with_padding.
I used nrf_crypto_aes_cbc_with_padding as base, copied it to another folder...
