I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello, I wanted to migrate from sdk16 to sdk17, So according to this topic I solve all pre compiling errors, then when I tried to download the code on my board(nRF52832) I...
In the Buttons and LEDs page, the LEDs are connected to P0.28-31 but in the connector interface page, the Figure 1 show LEDs connected to P0.13-16.
Buttons pins also looks...
Hello,
I am trying to create an application on my nRF52-DK using several custom service peripherals, each with 2+ characteristics. I have completed a few tutorials on...
Hi,
I am using USB device CDC, and the COM Port name on the PC is "nRF52 USB CDC BLE Demo (COMX), see the picture below.
How I can change it ? can I change it from...
Hi,
I followed the instructions described on https://github.com/NordicSemiconductor/pc-nrfconnect-launcher but I cannot "Start scan" within nRF Connect. It's greyed out...
Hi,
We just received prototypes of a new board with the nRF52840 and now we have a reset problem.
When the board is reconnected after a long time (no voltage remains on...
Hello,
I am testing the multilink BLE (1 central : n peripheral) UART example.
I am using Github code and tested it.
The central example is(SDK 16.0.0):
https://github...
Hi, I've just compiled clean examples from Zigbee and Thread SDK 4.1.0 and I'm following instructions from here: I've got CLI on the nRF dongle and multi_sensor example loaded...
Hi Nordic experts:
I am working with sdk 17.0.2 nrf52840 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine...
Hello everyone.
I want to assess the range of my current setup, theoretically. And I found this useful online "calculator": www.bluetooth.com/.../ (please scroll down until...
Hello,
I wanted to implement WDT resets when my application hangs. I am working on the advertiser code, what I observe was when I implement WDT driver in SDK 15.2 examples...
Hi,
I have been working with mesh and I'm using the version 4.2 Mesh SDK.As I understand it I should use nrf_mesh_serial_tx() api to send serial message.When I use this...
Hi There,
I'm working on a datalogger project using nrf52840, includes BLE also. I'm using external 24 channel ADC and should be able to log data to the SDCard at the rate...
Hi, can you explain shortly is it possible to use OTA functionality from FreeRTOS application? I wasn't able to found such an example, and I'm wondering about the possibility...
Most times the Online Power Profiler doesn't even load the graphics, etc. 80% of the time it doesn't finish loading and I have to reload multiple times. I have a 1 Gigabit...
