I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
We are trying to connect to NB-IoT network but seems nrf9160 not able to connect. We are trying with an NB-IoT SIM in Malaysia. Below is the log captured using LTE Link...
I want to change DLE/MTU in udp (IoT) example in order to test throughput with max mtu, is it possible?
The udp example does not contain nrf_ble_gap library, is it possible...
Relative newbie here. Would like to interface an Arduino MCU (AVR 328p/32u4, etc) via UART protocol with a decent range (50-100m open air) nrf 52840. I found the Fanstel BT840F...
Hi,
I have been struggling with this for 2 days now, and I cannot get my head around the problem.
I want to send data from my nrf9160-dk to Azure IoT Hub via the sample...
Hi,
I'm using 51822 QFAC SDK11 S130. The 51822 will receive a group of 18 bytes data from the phone. I'm facing a strange issue: every time after the BLE is connected, I...
Trying to run the experimental nfc pairing reference on a couple of 840 DKs for Bluetooth pairing as it's shipped in SDK 17.
Successfully compiled the micro-ecc make files...
Hi,
I get sporadic softdevice assertions at the address above. I am using S132, SDK15.2.0 on nRF 52832 custom board, and the problem started when I added LoRaWAN functionality...
Hi,
Recently, we were trying to support the HID device OTA function.
We have make an user control panel which could read the device FW version via driver which communicate...
I am starting with the Zephyr sample "peripheral": developer.nordicsemi.com/.../README.html
This sample started out with a Heartrate Sensor Service and a Current Time Service...
Hi,
Just a general question, is there a way to find out the exact size of the advertising packet? I'm using nRF52832 to connect to a smart phone. I was curious if there...
Hello, I try to read from IM69D130 (as microphone) by nRF52832 (SDK 16) , And I work with PDM driver of nRF52. It seems it cannot read the data correctly. Here is my function...
Hi! Reading the documentation on NRF_PWR_MGMT_CONFIG_DEBUG_PIN_ENABLED, I'm left with a few questions.
1. Will this pin be set in all system sleep states? i.e System on...
Hello Everyone.
I'm getting falls values on the power profiler, I just connected a 1K resistor across the External DUT and the voltage is 3.6V so expected values should...
