Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
Our design uses Laird's BL652, which uses nRF52832. I need to calculate the maximum clock drift of timers given the crystals used in our design. Our application uses...
Hi,
When I tried to use BLE5.1 phase data to achieve direction finding, I found a phase shift between reference period and the first slot, as the below graph shown:
...
Hi DevZone!
I would like to use nrf9160 for sending/receiving data by interfacing it with my microcontroller over UART and sending AT commands. I have a nrf9160 Feather...
Hello, support team.
In my SDK, I created two app timer.
What I expected is
- 1st handler called every 1 msec.
- The other handler called every 100 msec.
But...
This "BUG" is observed on nrf52840 DK (chip version is version 2 from *(UINT32*)0x10000134UL).
When NRF_RADIO is set to TXADDRESS 0 and RADIO_PCNF1_WHITEEN_Enabled...
...
Hello,
I am using VS Code 1.48.2 and building the C++ application code on nRF52840 dev board using "west" commands.
I have the following structure
project_directory...
Hi,
With the latest SDK (17.0.2) I try to use the SAADC module in blocking mode but when I call <nrf_drv_saadc_sample_convert> an ASSERT is always triggered in <nrfx_saadc...
Hi. I'm developing central device for IoT system.
Everything is going well, but there are some problems on connection precedure.
I tried to conenct 7 pheriperal(nRF52832...
Hello,
The question is really this - when using DECODER.LOAD=WaveForm mode, do I have to provide all four values even if the outputs 1-2 are not used? Or will it suffice...
Hello all.
I need to detect when data is received on RX. I am planning to use it with PPI channel so i could instantiate a task to it.
I tried to use nrf_twi_event_address_get...
Hello,
I need someone to shed some light on how to use the 'reg' node property because I am confused.com .
On this page https://docs.zephyrproject.org/latest/guides/dts...
Hi,
After a connection long push event does not work! But before a connection long push works fluently.
I could not found the error.
Thank you for your interest.
...
Our group is trying to use the NRF52833DK do phase-based distance estimation as described in the attached paper. To do this we want to transmit packets with constant tone...
Hey There,
I have one problem more. With my .cs Script I am opening a USB Port on my Raspberry, to communicate with my Nordic Thingy 91.
I can Read what the Nordic is...
Hello,
I want to read the CA certificate stored inside the modem, unfortunately the modem_key_mgmt_read function cannot read a certificate bigger than 2kb even if CONFIG_AT_CMD_RESPONSE_MAX_LEN...
