I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
We are developing the project based on nRF52840 chipset. We are configuring the chip for mesh application and using generic on/off model to send the data on the mesh...
Hello ,
There is two kind of clock source as i can see from the sdk files;
one of them is cpu that is ok but for the first one i couldn't figure out it's source "NRF_SYSTICK_CSR_CLKSOURCE_REF...
Hi all,
I've got some code running on my nRF9160dk that is behaving oddly. LED 3 blinks as expected (2 seconds on, 1 second off) but GPIO 10 (pin 18/ULTRASONIC_TRIG) remains...
Hi all, I'm a little blown away by the complexity of logging for this application (its highly likely I'm missing a few key elements to my understanding). I'm under the impression...
Hello, I read the instructions here for using the Nordic NRF Connect app for testing the CTS example: https://devzone.nordicsemi.com/f/nordic-q-a/53382/implementing-current...
Hello,
Hardware: nRF52840
SKD: nRF5_SDK_16.0.0
SoftDevice v7.0.1
I am working on creating a multilink central application where my central device connects to 3 peripherals...
Is there an issue with releasing application firmware, say v1.0 with and then in a following release via DFU, say v1.1 with .
I'm trying to understand if a network has been...
The nRF52832 (QFN package), Pin 44 is listed as "No connect" and has an additional description of "Leave unconnected". Question is what negative affect would occur if this...
Hi
I am unable to configure the nrf52840 dongle in client mode in light switch mesh example. I have changed the simple_hal.h to include the dongle board as /** Boards with...
I developed a software based on Blinky. I have been trying to add DFU to the current iOS app which is working properly to be like the Android app.
As I did in Android, the...
Hi, I would like to skip pairing process alltogether and just provide the KEys which were generated for both devices beforehand. My question is only. Is it possible to initate...
I have an application that will have up to 20 devices communicating with a gateway. Each device will need to send around 2MB of data every 5 minutes. We would like to use...
Hello.
I try to BLE and GPIOTE.
The reason for using GPIOTE is to read data from the temperature sensor.
And I want to sending data of temperature sensor by BLE...
Which type of PCB antenna should i use for BLE beacons based on nRF52832, nRF52840 and nRF52805 for longer range applications.?
Can i use the same antenna used in nRF52DK...
