I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
1. When I loaded the 9160 project, I had problems,
arm-none-eabi-gcc.exe:error:CreateProcess
9160 development environment, the required software, I have installed...
To the kind attention of Nordic support team,
we are building some demo program for evaluation purposes using your sdk16 examples with freertos, ble, usb.
But we also...
Hello Nordic people,
Is anyone knows how to set the Nrf52840 buttons high automatically without human interface while button press?
Any examples or Related API are available...
Hi there. When nrfx_gpiote_in_init's event handler is called, is it being called as an interrupt? I note that if I use NRF_LOG_INFO within the body of the event handler, then...
Hi everyone,
I am following the qspi example to communicate with MX25R6435F flash memory. This is my first time interacting with a flash memory and I have some questions...
Hello!
i´m enable ble long range like central for scanner beacons, i can see long range beacons, but only one time, then i need to restart my DK: i use to do this ble_uart_c...
Hello,
As per your given link in 1.2 Build and flash - using SEGGER Embedded Studio ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
Hi,
It appears that at least one Mesh_v4.2.0 example (light switch) will not link under nRF5_SDK_17.0.2.
I managed to get Mesh examples to run under SDK_17.0.0 a while...
I have a new Bluetooth remote product in development that has a bluetooth stack that will incorporate HID, BAS, NUS, ANCS, and buttonless DFU services. I have the HID and...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm getting this error while trying to connect with my device in the "ble_app_hrs_c".
"Connection...
I have found a few "how to" on cofiguring Eclipse for application development on nRF52 devices. After some point things are not as described in this guides. So, Is there any...
I'm trying to create a read event whenever a certain characteristic is read. I used BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event to monitor that. I also set "is_defered_read"...
Hello,
I am developing a composite HID peripheral based on the nRF52840 that can connect to a PC either via USB or BLE.
I am using SDK 15.0.0.
Regardless of the connection...
When I build and run an example Bluetooth: Peripheral HIDS keyboard (it's the same for master branch and v1.3.2) using nRF52840 DK I faced one strange behaviour. To simplify...
I just downloaded the latest version of the pc-ble-driver hoping some of the bugs I had reported were fixed. The downside is the notes do NOT indicate they were addressed...
