Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
Hi,
I am trying to disconnect an Android smartphone from the nRF52840. After trying for some time we found out that the BLE stack of Android does not reliably closes a Bluetooth...
hi..folks
wish you happiee new year
i am using nrf52832 whille i tried to pair my device with my android , i am getting an error message " pairing rejected by nordic_uart...
Hi,
According to below thread, the advertising interval has a random 0 - 10 msec delta, so if the adv interval is 20 mses, if run it for long enough, will the result be...
Hi,
I would like to use the PDM interface for my application in nrf52840.
I configured the driver, and started using the SDK's API successfully.
Question 1:
During...
We want to achieve something like this -> We have several BLE peripherals with us and we are going to connect this peripherals to nrf9160 using nrf52 module and then send...
Hi,master
I want to learn DFU/bootloader, I am looking at the official source code, but my ability is too bad, I can't understand it at all. Is there any detailed information...
Hi
I read some threads about how to pair/read IKEA Trådfri.
I'm using nRF5840 dongle with the HEX code cli from SDK 17.0.0.
Using the terminal and send
bdb role...
I have both a NRF52840 (actually 2) and 2 dongles. I need to measure RSSI vs distance for a single link. I set up the RSSI viewer and it shows a blue or green bar for the...
I am getting unexpected behavior when using the latest version of the antfs.c sample code. I think this is a separate issue from what I reported here
When the ANT-FS download...
I've been experimenting with your online power calculator: https://devzone.nordicsemi.com/nordic/power/w/opp/2/online-power-profiler-for-ble for NRF52840. I see that the idle...
