I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
hi Guys,
before i shoot myself can someone answer me this simple question .... for most.
In the segger embedded software nrf to sdk do i need to complete stages 1-4...
Hi everyone, I am looking for an external oscillator on the nrf52840 DK that can take its own power and is similar to a push button that can make a voltage change on the GPIO...
Hi!
My BLE peripheral needs to change its "static" passkey under certain circumstance.
However, when I attempt to connect after setting it, I get a PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING...
Hello everyone,
I'm trying to interface a NiceRF LN610 LoRaWAN chip to nRF52840 via UART. Initially, I tried communicating with the chip using CP2102 USB-to-TTL module and...
Hi,
In order to measure the RF power, I measured the RF power by radiating inside the RF shield box.
But there is something strange.
The position between the device...
Hi ,
I want to develop the firmware to read the nfc tag and read the sensor data send to the application via BLE I have read many post regarding nfc . Let me explain what...
Hi,
I am working on temp. sensor with nrf52832 dev kit for firmware testing and development and also using nrf52810 for product testing.
in my code, I merged twi communication...
hi,
I want to develop a project based on ble beacon mode and ble app hts code.
and I am using nrf52810. so will it work if I merge both codes and use for this project...
I know that nrf_cal_set_time() from the nrf calendar example is NOT meant to be called on a regular basis / should only be called to update the time being kept locally to...
Hi,
We are looking for a guideline to trigger GPIO and SAADC sampling at the same time.
Our purpose is to sample every 20 m
Hi,
We are looking for a guideline...
Hi, We have a DFU OTA process that was functional, but updating our softdevice to s113 7.2.0 has left us with a problem - since the softdevice does not exist in the nrfutil...
Hello.
I am doing a small project where nrf52 reads data from a BME280 temperature sensor via SPI and sends it using ESB.
I have no experience with radio, so I use a ready...
I would like to use the NRF24L01+ from a 3v coin cell, but interface it over SPI with a 1.8v-powered microcontroller. Assuming the uC is tolerant of the NRF SPI outputs, I...
We have a application where data transfers happen through a mechanism where the external client does a write-without-response to send in a command. The response to the command...
I am busy with my first BLE project , programming a custom service for both pheripheral and central role. I have already finished the pheripheral service, using a custom service...
