I'm having some issues regarding the data update interval when running the asset_tracker_v2 application, particularly with adjusting how frequently it publishes data to the...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
I am working on nRF51-DK with nRF51422 with softdevice S130 and SDK 12.3.0.
I see that GPIOTE driver provides sensing for signal transitions like NRF_GPIOTE_POLARITY_LOTOHI...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
Hello,
I am trying to get acquire the accelerometer data every 4 hours for a sample duration of 60secs. These data are stored in RAM and on ble connection with the mobile...
Hi,
I'm totally new to programming nRF DK's.
What am I using?
Segger Embbedded Studio for ARM (Nordic Edition)
Toolchain: nRF Connect SDK v1.4.99-dev1
The "mqtt...
Hello there,
Since we use the lower level modules from Nordic's SDK for Mesh 4.2.0 - namely timeslot.c, bearer_handler.c and some additional modules to make them work properly...
Hi,
I just happened to stumble across these lines (123 to 126) in nrf_drv_uart.h:
And I noticed that on line 125 NRF_UART_ERROR_FRAMING_MASK is mapped to NRF_UARTE_ERROR_PARITY_MASK...
Hi, I've got our custom board with W25M02GVZEIG and I want to be able to read it out in a way that is fast and works with XIP. It's ok if it takes more time to write.
So...
Hi, I've made UART (BAUD RATE 1M) only on central after recieve all data (8kB). Peripheral is sending data from own ram (collected data from SPI sensors). What and how i need...
Hi,
I am trying to start from scratch BLE firmware to send and receive data from the development kit PCA10100 and nRFConnect App. I am following this course on Github here...
Hi,
i am trying to send temperature data along with timestamp as a string over BLE to a smartphone. i did the temperature reading part and now want to add timestamps to...
Can you show how can I merge the ble_app_uart and ble_app_uart_c into one code?
Once the device wakes up, it will check its GPIO - if it is '0', the peripheral will start...
