Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello
I have written some code to write the nrf51822 via SWD. It all works, but I would like to make it faster.
I am currently writing one word at a time. If I read...
Hello dear friends,
I'm trying to bring up a Raytac module for the first time. I was able to program S110 7.1 and I'm using the Beacon example found in the SDK 6.1
But...
Is there a similar way tot get the radio's MAC address when using Gazell only (no BLE)?
In SoftDevice there is a "sd_ble_gap_address_get()" function call.
Hello All,
I'm trying to program a NRF51822 module for the first time. I'm using the Jlink for ARM from IAR which is segger rebranded. It supports JTAG and SWD.
We got...
Hi,
I am trying to obtain a 10khz PWM (50%) on an output using Timer2 (see code below). It is working fine up to around 500Hz (2msec), above that (1kHz) I am getting only...
I would like to develop an application with nRF8001 DevKit. The master emulator of this kit is an USB Dongle and it is originally meant for PC connection. My final goal for...
Hi all,
Problem: Second harmonic with nrf905.
I used nRF905 and exact recommended design&layout in the datasheet. Now, it is said that there are 2. order harmonics ...
It seems that the all the msc_inline_*.png files are missing from the SDK 6.1.0 documentation directory.
For example:
file:///C:/Nordic%20Semiconductor/nRF51%20SDK_v6...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
Hi All,
I would like to broadcast 256 byte data in one shot every second, any reference in SDK recommend?
Thanks in advance.
**updated at 19 Sep, 2014
Application...
Nordic,
After upgrading to S110 7.0.0 the BLE_LBS example no longer works as downloaded from GitHub. I adjusted the flash algorithm size which fixed the first problem and...
Hi Developers,
I'm using an nRF51822 and finally beginning to understand BLE. I want to learn by example so I downloaded NAN-36.
Im at a point where the Application...
